mbatchelor

CONTACT INFORMATION: Matthew M. Batchelor Alces Imaging and Automation, LLC 2906 Blue Wind Court Houston, TX 77084 Phone – 281-646-7477 Fax – 281-599-8780 E-Mail – matthew.batchelor@alces.us

About

Username
mbatchelor
Joined
Visits
632
Last Active
Roles
Member

Comments

  • 2018-02-13-085444 Svenja -- I read your message and then did a test. Here are the results. Please remember that if your ROI is small enough that the % CHANGE that you have requested is less than 1 pixel, the WIDTH or HEIGHT cannot change. Also …
  • 2018-02-12-162628 Svenja -- I see your message and I believe I understand your request. I cannot try it right not but I believe this will happen if you set everything up on the CAT with the GET BUTTONS and then switch to the DOG and press CREATE …
  • 2018-02-06-180422 JuanMartin I agree with YURI that the LINE PROFILE TOOL is a great tool for this challenge if the IMAGES will cooperate. Here are some SCREEN CAPTURES that might give you an idea about how to tackle this challenge with that tool…
  • 2018-02-06-174651 Svenja -- I have tested the     Smart Roi Project V1A and I believe that you can use it on multiple images without restarting the APP or PREMIER. I believe what may be missing in your use of this app is the proper use of the …
  • 2018-02-06-170644 JuanMarin -- I believe I understand your problem. I believe that you would like to measure the lowest point in the upper edge of a moving feature. There look to be some complicating factors but here is an example which may giv…
  • 2018-02-05-055159 Svenja -- Thank you for the compliment. The PROBLEMS you listed and my ANSWERS are below. My calendar for this week is very busy but I will try to address your PROBLEMS and provide better ANSWERS late today (MON) or late tomorr…
  • 2018-01-29-153851 All -- With guidance from MEDIA CY TECH SUPPORT, I did the following: DEINSTALL CAPTURE INTERFACE SOFTWARE = CHECK DEINSTALL LUMENERA SOFTWARE = CHECK REBOOT = CHECK DISABLED WINDOWS DEFENDER = CHECK REINSTALL LUMENERA SOFTWAR…
  • 2018-01-29-151253 All -- I would like to add a bit of additional information to this query . . . All of the HARDWARE and SOFTWARE in the above issue were working together successfully when the computer was a brand new out of the box WINDOWS 7 CO…
  • 2018-01-25-162519 Uemoto -- I do not know what it takes to get the HISTOGRAM STATISTICS into a STRING right off the bat but here is CODE that will put STRING S on the WINDOWS CLIPBOARD                 'Put the current line on the clipboard       …
  • 2018-01-24-131834 Dhavas -- There may be a more sophisticated way to do this but I would use MASKS and HOLE AREA and HOLES NUMBER. A path through this is shown below where: AA is the ORIGINAL IMAGE with the ROIs and the AREAS found within the RO…
  • 2018-01-24-131603 Nikita -- Sorry that I did not make it clear that the ORIGINAL IMAGES were being closed. I thought that With Adjust.ImageCommands.Define(NewMacro) .Run(var1, image1) End With was connecting with t…
  • 2018-01-24-113535 Nikita -- I loaded the IMAGES into IMAGE COMPARE and ran the NEW MACRO CODE on PREMIER 9.2 and it worked. If I used CODE to load the IMAGES into IMAGE COMPARE it did not work. As mentioned before, the CODE to load the IMAGES in…
  • 2018-01-24-092226 Nikita -- Thank you for your response. I would like to avoid what seems like MAJOR SURGERY to resolve what seems like a MINOR ISSUE. I will transfer the app to my other computer which has PREMIER 9.3.3 and try it there.  If it …
  • 2018-01-23-164939 Nikita -- Checking WWW.MEDIACY.COM, the latest PREMIER 3D seems to be the V9.3.2 I am running. This is shown below. Any further thoughts on a way to make the CODE control the IMAGE COMPARE? Thanks. -- Matt -*-*-*-*-*-*-*-*-*…
  • 2018-01-23-143944 Nikita -- If I move the layers/images around manually before I run your NEW MACRO, the correct image is selected. When I add the SET ANGLE to it, everything is turned though Public Function NewMacro() As SimpleScript …
  • 2018-01-23-134342 Nikita -- Thinking that the IMAGE COMPARE TOOL might have been confused by all of the TRIAL and ERROR that it has been subjected to, I: ** shut down and restarted PREMIER ** opened the two images manually ** loaded the two image…
  • 2018-01-23-133826 Here is the PRODUCT and VERSION information.
  • 2018-01-23-120256 Nikita -- I tried to apply the information you gave me and I was not successful. I went back to trying to RECORD and MODIFY and I have bumped into a similar issue. The RECORDED CODE applies the TRANSLATION and ROTATION to both …
  • 2018-01-23-111415 Nikita -- Thank you for your response. I will try to weave the information you have provided into the CODE. I will update with the results ASAP. Thanks again. -- Matt
  • 2018-01-22-201614 Nikita -- I have attempted to use the INFORMATION and CODE you provided and I have mixed results. The QUERY for the X, Y, and ANGLE works like a champ.  Thanks. The SET for the ANGLE (I have not tried X and Y yet) is not worki…
  • 2018-01-22-155248 Nikita -- Thank you for the INFORMATION and CODE. I'll be working on that project this PM and the only other thing I think I may need is to know if you have any suggestions to address "Q3) What FUNCTIONS would allow the CODE to…
  • 2018-01-22-100922 All -- Can CODE within the PREMIER WORKBENCH control the IMAGE COMPARE TOOL as queried above? Thanks. -- Matt
  • 2018-01-10-193052 Amanda -- There is not enough information in your message for me to understand your problem completely. Is the image that is being analyzed being captured from a CAMERA connected to IMAGE-PRO PLUS or is it an image being opened …
  • 2018-01-05-105558 BillKline -- There is not much information in your message but it sounds like the CONFIGURATION for the CAPTURE TOOL of IMAGE-PRO PLUS has changed to the SIMULATION MODE rather than the actual CAMERA MODE. Within the DIALOG BOX …
  • 2018-01-04-104236 Yuri -- Thank you for this diagnosis and resolution. I'll make use of this in future applications. -- Matt
  • 2018-01-04-093012 Yuri -- Thank you for the compliment. Svenja -- I did the DEVELOPMENT and TESTING on this PROJECT / APP in PREMIER 3D 9.3.2. There is CODE within the APP to handle the case of NO IMAGE, NO CALIBRATION, and NO ROI. When I star…
  • 2018-01-03-132546 Sorry. I thought I did. Here it is. -- Matt
  • 2018-01-03-090917 Svenja -- The CODE in the     Smart Roi Project V1A.ipx IPX FILE needs to be loaded into the PREMIER PROJECT WORKBENCH before you will see the     SMART ROI APP V1A BUTTON in the APPS SECTION of the APPS RIBBON. Instructio…
  • 2018-01-02-171209 Svenja -- I took some time this afternoon and created a SMART ROI PROJECT that includes a SMART ROI APP. The DIALOG BOX for this APP is shown below. The IPX FILE which contains this PROJECT / APP is posted here as     Smart…
  • 2018-01-02-092137 Svenja -- The SMART ROI TOOL that I described is not a FEATURE of PREMIER but it is possible through CODE running within the PROJECT WORKBENCH. I believe it would take me about an hour to DEVELOP and TEST the CODE for a SMART RO…